Cars without BT module or Built-in BT module
Posted: Tue May 04, 2021 7:57 am
Cars without BlueTooth module
For cars with RNS315, RNS510, RCD300, RCD310, RCD320 , Composit Media STD (5K7035200, MIB2 STD 5C0035680 US , EU, 5L0035680, RCD330
Require SWCM(16) - LowLine , if you have HighLine - need to be recode to LowLine
Find (BLACK) socket which keep connection between PCB and Slip Ring flexi and take it off from PCB
Desolder/remove connector number 3 and 4 from PCB
Solder together connectors with pins 1 ,2 for better connection
Solder input wires ( RED and Yellow) to 3 and 4 , make sure wires not touch any move parts inside 9use heat shrink)
Solder main wires to main socket (if you not use MFSW with CCS, ignore WHITE cable)
Check / change if need wires in Airbag loom (samples below)
Assembly all and put it back to the car. Install MFSW module with double side tape or Velcro on the steering column
Install proper stalks
THIS IS VERY IMPORTANT , YOU CAN NOT KEEP WIPER STALK with TRIP computer for example or code SWCM to Board computer via Wiper stalk , otherwise instrument cluster might freak out and cannot be operate from MFSW as should be (scroll left / right)
After proper CAN and POWER connection BLUE LED stay ON (go OFF after Ignition OFF)
When you connect MFSW over LIN wire WHITE LED start flashing, when you press CCS button (CCS is ON) , Green LED start illuminate, when module is working RED led illuminate, when module go to “sleep” RED and other led are OFF
Open VCDS and go to 16th controller and code for your car
After proper connection , please read coding desctriprion and code module depend of your new MFSW
viewtopic.php?f=41&t=240&sid=88a9a92d11 ... cbe5324bb0
For cars with RNS315, RNS510, RCD300, RCD310, RCD320 , Composit Media STD (5K7035200, MIB2 STD 5C0035680 US , EU, 5L0035680, RCD330
Require SWCM(16) - LowLine , if you have HighLine - need to be recode to LowLine
Find (BLACK) socket which keep connection between PCB and Slip Ring flexi and take it off from PCB
Desolder/remove connector number 3 and 4 from PCB
Solder together connectors with pins 1 ,2 for better connection
Solder input wires ( RED and Yellow) to 3 and 4 , make sure wires not touch any move parts inside 9use heat shrink)
Solder main wires to main socket (if you not use MFSW with CCS, ignore WHITE cable)
Check / change if need wires in Airbag loom (samples below)
Assembly all and put it back to the car. Install MFSW module with double side tape or Velcro on the steering column
Install proper stalks
THIS IS VERY IMPORTANT , YOU CAN NOT KEEP WIPER STALK with TRIP computer for example or code SWCM to Board computer via Wiper stalk , otherwise instrument cluster might freak out and cannot be operate from MFSW as should be (scroll left / right)
After proper CAN and POWER connection BLUE LED stay ON (go OFF after Ignition OFF)
When you connect MFSW over LIN wire WHITE LED start flashing, when you press CCS button (CCS is ON) , Green LED start illuminate, when module is working RED led illuminate, when module go to “sleep” RED and other led are OFF
Open VCDS and go to 16th controller and code for your car
After proper connection , please read coding desctriprion and code module depend of your new MFSW
viewtopic.php?f=41&t=240&sid=88a9a92d11 ... cbe5324bb0